Rokform Motorcycle Phone Mount - Secure Quad Tab Twist Lock & Built-In Magnet for Harley, Metric, Indian Cruisers - Perfect for Adventure Riding & Daily Commutes

I own two Harley Davidson motorcycles. One is a bagger and the other a soft tail. I wanted a phone mount that I felt comfortable that my iPhone 8+ would not be lost or damaged. The mounting of the case to the phone is every bit as good or better than my prior Otter box case. I also purchased the magnet that attaches to the vent louver so I can use it in my car. It truly works great! The system is excellent and my wife wants the same for her Samsung Galaxy phone. The phone cases and other accessories I give the Rokform products 5 stars and nothing less.When I received the first Rokform mount to install on my Electra Glide Ultra Limited I did have a mounting issue. Using the necessary Torx bit I removed the original two attaching bolts and the bracket that Harley Davidson secures the Master Cylinder and Front Brake assembly. The original Harley Davidson installed bolts when I checked protruded about 1/2” to 5/8” through the half bracket and there was a lot of thread to hold the assembly in place on the handlebar. See photo attached.I took the Rokform parts as supplied in the kit and assembled them in my hand using the longer furnished bolts from Rokform. What I found was the bolts supplied by Rokform in the kit extended through the half bracket with barely 3/16” of the bolt protruding and about 4 threads. The bolt used is a standard 1/4 x 20 thread, but utilizes a countersunk head and is finished with a black non-corrosive finish. See attached photos that I sent to Rokform. First photo shows how short the supplied bolts in the Rokform kit were. These if used would have eventually stripped out the attaching aluminum master cylinder and brake assembly leaving an expensive repair. The second picture shows the original bolt length as it was manufactured and how much longer the thread engagement is.I contacted Rokform whom responded back to me very quickly. I explained what I had found and advised I needed two longer bolts of the same thread only longer and with the same black finish that wouldn’t rust. The original person I spoke with forwarded me to a person at Rokform who was a technical person. He and I spoke and I sent in the same photos attached with a few additional. The issue is apparent! Bolts were simply too short. However I spent a week dealing with this guy as he went to the area Harley dealer to attempt to look at new bikes such as mine, and validate my complaint. Why did I bother sending photos?After a week I got tired of waiting and dealing with this guy. I called around to an area fastener supply and asked if they had such a bolt I needed in the correct length. As expected they did and I went there and purchased two.In a day or so I again got contacted by the guy at Rokform who told me he could not verify my issue on any new Harley at the dealership he went to there in California. At this point I was aggravated and told him that I got it resolved by taking my time and going and buying two bolts of the correct length. I also conveyed my disgust with him and this nearly two week long deal to get two longer bolts. He advised he would furnish me longer bolts and in a few days they arrived.In summary I really like the Rokform phone mount. So much so I bought another one for my Harley FatBoy. I haven’t yet installed it as I keep that bike in Florida. however when I do if such a bolt length issue occurs I’ve likely got bolts long enough to adequately secure it. I don’t understand why I had to prove to the guy and he had to validate my complaint. I figured that Rokform would simply furnish me without issues two longer bolts. I truly think for the price of this phone mount kit that multiple length fasteners should be furnished in the kit. I purchased a cup holder made by Kuryakyn that is a perch mount as well and mounts on the opposite handlebar assembly. It came with four sets of fasteners. Two were standard thread and two were metric thread. That cup holder kit was expensive just as this Rokform phone mount and Kuryakyn didn’t go cheap in furnishing you what you could possibly need to mount their product. As I stated I bought a second Rokform mount and will likely by a third as I plan to buy one for my Son to give to him for one of his Harleys. Rokform did come through on the customer service end finally. However I don’t understand why such a simple issue took so many phone calls and discussion. I believe that Rokform thinks that a installer won’t remove the half bracket to install their perch mount such as I did. They believe you will remove one original bolt and then loosely assemble the phone mount using their furnished hardware. I’m an ole guy and have learned to trust no one but God. I’m glad I checked the length of the bolts furnished as had I didn’t they could have pulled the threads out of the aluminum Harley Brake Master Cylinder assembly. I would have then been facing the cost of repair as Rokform wouldn’t for sure. I could have simply just went and gotten the bolts and fixed the issue and said nothing. However I wanted Rokform to know and be aware of the issue. This forum we have to help each other by advising others of possible product issues is excellent. This Rokform Phone mount is an excellent product no question! Just check to be sure the bolts you get to attach your Rokform perch mount design if that’s what you buy, are long enough to adaquately secure it as the original manufacturers bolts. Hope you felt this was worthwhile for you to read.I like the ease of install!! I feel with it installed in the location of the handbrake or clutch you don’t get a full view of the phone as you have to have it on an angle so it’s not in your way. They should make the screws longer and the bracket that holds the phone longer (maybe 8 inches oal) with either a pivot point in the middle or make it rotational there in the middle and it needs to something to counter that at the end to be able to adjust your phone to exactly where you want itHands down the best motorcycle mount ever.I was very skeptical on ordering this mount, mainly due to the cost and that it's sometimes hard to tell the quality from the video and the advertisement on Amazon. The mount could not have been any easier, I have a 2008, Black, Harley Davidson, Ultra Classic. The mount to the left (Clutch) housing was very simple. The mount comes with two types of spacers; I chose the shorter one. I removed the stock bolts and using the bolts and shorter spacers and a little blue locktite the mount is installed. I purchased the iPhone Rokform case and mounted it so the phone is horizontal. Brother, it not only looks cool it works. That phone is on there! Also there is a magnet in the case and mount that helps hold it together.OUTSTANDING PRODUCTIncluded mounting hardware is not sufficient. Considering the considerable cost of this mount and required case, the seller could likely afford to include several lengths of screws.Work excellent, tried others brands but they don’t even come close this is the best phone mount out there…. Awesome!!The phone mount was easy to install and fit my Sportster with just a bit of testing the various spacers that came with it. I purchased the Rokform – Universal Adapter with Twist Lock, Magnetic Phone Mount and stuck it to my phone case. I have ridden about 1000 miles with my phone mounted and have full confidence that it is secure.The only improvement that I could suggest is to add another adjustment. The arm rotates and pivots at the mount point but it doesn't rotate around the axis of the arm itself. So with the phone mounted sideways the angle of the clutch mount has it facing my belly. This has only been an issue once when I didn't understand the navigation voice instruction. Instead of a quick glance at the screen, I pulled over and removed the phone from the mount to look at it.I purchased this item to fit a 2002 sportster.Unfortunately the bolts are about 1/4 inch to short and the threads don’t engage the thread on the clutch mount.I would contact the seller to ask them about sending new hardware however there dose not seem to be an option for this.Otherwise the mount looks to be of good quality.Doesn't work with the kawasaki vulcan SThis rockform support is very stable and holds the phone very well. I have a modified Harley Davidson and it shakes like crazy but I never had a doubt that this support would hold my 2k$ phone without an issue.Had a friend that had an accident and had this support for his phone. The handle bars flew away from the bike on impact but the phone stayed on the support. We were both amazed about this. Very recommended!The product looks great but it did not fit my Honda CBR650R the screw hols were much wider than those on the CBR and i could not align them together and tighten the screws.I do not recommend it for CBR sport motorcycles.Therefore I returned it and placed another order of the same product with the one that can hold the handlebars with much higher price.I would have given it more rating if it wasn’t for the pricing.